Mass Flow Meter - Nitto Seiko UAE

Nitto Seiko Mass Flow Meter

A mass flow metre called CLEAN FLOW achieves great performance and high dependability. By sensing the phase difference created by Coriolis in the measuring tube, it is able to measure mass flow directly. An easy-to-use capacitance touch panel is a feature of the high-functioning transmitter. A variety of indication articles can be put on the three LCD lines.

Original Products
Warranty Against Defects
Returns & Refunds Policy
Ships Worldwide
Dedicate Support

Need Help? Call + 971 4 3330105

Email Your Query

It can measure mass flow directly, it is not affected temperature, pressure, viscosity, density, or flow distribution due to its measurement
Compact design
It does not need special fixture. Easy
New type measuring tube realizes low pressure
Various indication article by 3 line
Good visibility by Buck-light
Plug-in card can add out/input easily. (Option)

Sensor

Size			015	025	050	080	100	150
Nominal diameter			10A, 15A, 20A, 25A, 40A, 50A, 65A, 80A, 100A, 150A, 200A
Connection end			JIS10K, 20K ASME/ANSI 150, 300, 600 JPI 150, 300, 600 DIN PN16, 40, 63 Tri-clamp
Fluid			Liquid/Gas
Flow range			0 ～ 860,000 Kg/h (6 type)
Accuracy	Volume	Liquid	General: Mass flow ±0.4% Volume flow ±0.4% High accuracy: Mass flow ±0.15% (±0.1%option) Volume flow ±0.15%
		Gas	General: Mass flow ±1.0% High accuracy: Mass flow ±0.5%
	Density	Liquid	General: 0.010kg/L High accuracy: 0.002kg/L (0.001kg/L option)
Temperature			General: -50 ～ 160 ℃ High accuracy: -50 ～ 205 ℃ Explosion-proof type is depending on the specification
Pressure			Depending on the connection end
Wetted parts material			Stainless steel (Standard), Alloy C (Option)
Explosion-proof			ATEX / IECEx, cFMus, TIIS (Applying)

Transmitter

Power	100 ～ 240V AC, 50/60Hz 11 ～ 30V DC
Power consumption	20W
Protection level	Unit type : IP65 / IP67, NEMA 4X Remote type: IP65 / IP67 / IP68 (Sensor only, Immersion depth 5m), NEMA 4X
Housing material	Aluminum Stainless (Remote type: Option)
Output signal	Analog: 4-20mA DC (Active mode or Passive mode) Digital: 2 points (Pulse or switch) (Passive mode) HART (Protocol Ver. 7.1)
Dumping	0.8 sec. (Avilable setting 0.2 ～100 sec)
Low cut-off	1% of Max. flow rate. (Available setting 0～5%)
Transmission distance	Max. 200m (Remote type)

Liquid mesurement

Size		015	025	050	080	100	150
Flow range	MASS flow[kg/h]	0～8,000	0～35,000	0～90,000	0～250,000	0.～560,000	0～860,000
	Volume flow [L/h]^（※¹^）	0～8,000	0～35,000	0～90,000	0～250,000	0.～560,000	0～860,000
	（※1）Volume flow is according to the 1g/mL of density. In case of other than 1mg/mL Volume flow = Mass flow / Density.
Zero-stability [kg/h]		0.64	2.16	7.2	20	41.6	68.8

Basic accuracy

Model	430 (General type)	450 (High accuracy type)
Mass flow (Liquid)	±0.4％ ±0.25％ (Option) ±0.20% (Option)	±0.15％ ±0.10％ (Option)
Mass flow (Gas)	±1.0％	±0.5％
Volume flow	±0.4％ ±0.25％ (Option) ±0.20% (Option)	±0.15％
Repeatibility (volume)	Refer to below table
Density (Liquid)	0.010kg/L	0.002kg/L 0.001kg/L
Repeatibility (density)	0.002kg/L	0.002kg/L 0.001kg/L

Measuring accuracy

Max. measuring accuracy

Repeatability

±General accuracy

±1/2×General accuracy

±（Zero-stability/Measured value）×100％

±1/2×（Zero-stability/Measured value）×100％

Meter size	Size (mm)				Approx. weight (kg)
Meter size	Ａ	Ｂ	Ｃ	Ｅ	Approx. weight (kg)
０１５	φ４４．５	７７	４６	３４０	９
０２５	φ６９．５	１０３	６２	３７９	１１
０５０	φ９９	１２５	８０	４１６	２７
０８０	φ１５５	１８３	１２３	５０５	７１
１００	φ１８５	２６１	１６８	６０３	１２３
１５０	□２６０	３２０	２０５	６９１	１８１

Remote type

Meter size	Size (mm)				Approx. weight (kg)
Meter size	Ａ	Ｂ	Ｃ	Ｅ	Approx. weight (kg)
０１５	φ４４．５	７７	４６	３４０	９
０２５	φ６９．５	１０３	６２	３７９	１１
０５０	φ９９	１２５	８０	４１６	２７
０８０	φ１５５	１８３	１２３	５０５	７１
１００	φ１８５	２６１	１６８	６０３	１２３
１５０	□２６０	３２０	２０５	６９１	１８１

015 sensor connection standard

Connection end	Specification code	Ｌ(mm)	Ｄ(mm)
10A JIS10K	015E1J1	385	90
15A JIS10K	015R0J1	385	95
1/2” CL150 (ASME B 16.5)	015R0A1	435	89
1/2” CL300 (ASME B 16.5)	015R0A3	421	95
20A JIS10K	015R1J1	421	100
3/4” CL150 (ASME B 16.5)	015R1A1	421	98
Conform to DIN 32676 1/2” Tri-clamp	015R0T1	413	34
Conform to ASME BPE 1/2” Tri-clamp	015R0T3	433	25

025 sensor connection standard

Connection end	Specification code	Ｌ(mm)	Ｄ(mm)
20A JIS10K	025E1J1	576	100
3/4” CL150 (ASME B 16.5)	025E1A1	575	98
25A JIS10K	025R0J1	525	125
1” CL150 (ASME B 16.5)	025R0A1	575	108
1” CL300 (ASME B 16.5)	025R0A3	576	124
40A JIS10K	025R2J1	576	140
1-1/2” CL150 (ASME B 16.5)	025R2A1	576	127
In accordance with DIN 32676 1” Tri-clamp	025R0T1	590	50.5
In accordance with ASME BPE 1” Tri-clamp	025R0T3	590	50.4

050 sensor connection standard

Connection end	Specification code	Ｌ(mm)	Ｄ(mm)
40A JIS10K	050E1J1	763	140
1-1/2” CL150 (ASME B 16.5)	050E1A1	763	127
1-1/2” CL300 (ASME B 16.5)	050E1A3	756	156
50A JIS10K	050R0J1	715	155
2” CL150 (ASME B 16.5)	050R0A1	715	152
2” CL300 (ASME B 16.5)	050R0A3	763	165
65A JIS10K	050R1J1	763	175
2-1/2” CL150 (ASME B 16.5)	050R1A1	756	178
In accordance with DIN 32676 2” Tri-clamp	050R0T1	740	64
In accordance with ASME BPE 2” Tri-clamp	050R0T3	740	63.9

080 sensor connection standard

Connection end	Specification code	Ｌ(mm)	Ｄ(mm)
65A JIS10K	080E1J1	910	175
2-1/2” CL300 (ASME B 16.5)	080E1A3	920	178
80A JIS10K	080R0J1	870	185
3” CL150 (ASME B 16.5)	080R0A1	880	191
3” CL300 (ASME B 16.5)	080R0A3	895	210
100A JIS10K	080R1J1	1060	210
4” CL150 (ASME B 16.5)	080R1A1	880	229
In accordance with DIN 32676 3” Tri-clamp	080R0T1	910	106
In accordance with ASME BPE 3” Tri-clamp	080R0T3	910	90.9

100 sensor connection standard

Connection end	Specification code	Ｌ(mm)	Ｄ(mm)
80A JIS10K	100E1J1	1275	185
3” CL300 (ASME B 16.5)	100E1A3	1244	210
100A JIS10K	100R0J1	1150	210
4” CL150 (ASME B 16.5)	100R0A1	1144	229
4” CL300 (ASME B 16.5)	100R0A3	1324	254
150A JIS10K	100R2J1	1300	280
6” CL150 (ASME B 16.5)	100R2A1	1330	279

Note) This size is for major item. Unavailable for manufacturing depend on the combination.

150 sensor connection standard

Connection end	Specification code	Ｌ(mm)	Ｄ(mm)
4” PN16 (EN 1092-1)	150E2D2	1569	220
6” PN16 (EN 1092-1)	150R0D2	1421	285
6” CL150 (ASME B 16.5)	150R0A1	1485	279
6” CL300 (ASME B 16.5)	150R0A3	1505	318
8” CL150 (ASME B 16.5)	150R2A1	1650	343
8” CL300 (ASME B 16.5)	150R2A3	1670	381

Note) This size is for major item. Unavailable for manufacturing depend on the combination.

Transmitter for remote type (Type FT)

Indication contents

Mass flow, Volume flow, Density, Temperature, and any others (Available for select).

4 kind of monitor for operator can be set, and it can indicate several measuring result simultaneously. Indicator has 3 line LCD, and variety of indication is available.

Operation

Operated by capacitance touch panel through the glass is available. Set according to the menu by 4 operation keys.

Standard output

Analog output: 1 point (4～20mADC/HART7） Digital output: 2 points (Pulse, frequency)

Optional plug-in cards (for additional output)

The transmitter has two slots in which plug-in cards can be inserted to provide additional inputs and outputs.

The slots are located on the transmitter motherboard and can be accessed after removing the front housing cover.

The possible combination of plug-in cards

Output code	Additional output code		Slot OC1 Terminals V1 / V2	Slot OC2 Terminals V3 / V4
Output code	Output 1	Output 2	Slot OC1 Terminals V1 / V2	Slot OC2 Terminals V3 / V4
G0	—	—	—	—
G1	×	—	24 V DC power supply (blue)	—
G2	—	×	—	Passive current output, 4～20 mA (red)
G3	×	×	Passive current output, 4～20 mA (red)	Passive current output, 4～20 mA (red)
G0	DRT	DSN	24 V DC power supply (blue)	Passive digital input (yellow)
G0	DRT	DSG	24 V DC power supply (blue)	Passive digital output (green)
G0	DRT	DSA	24 V DC power supply (blue)	Passive current output, 4～20 mA (red)
G0	DRN	—	Passive digital input (yellow)	—
G0	DRN	DSG	Passive digital input (yellow)	Passive digital output (green)
G0	DRN	DSA	Passive digital input (yellow)	Passive current output, 4～20 mA (red)
G0	DRG	DSN	Passive digital output (green)	Passive digital input (yellow)
G0	DRG	DSA	Passive digital output (green)	Passive current output, 4～20 mA (red)

Terminal block

IP rating

In accordance with EN 60529：IP65/IP67, NEMA4X

Vibration

In accordance with EN 60068-2

10～58Hz, Max deflection 0.15mm（Peak load） 58～150Hz, Max. acceleration 2G（Peak load）

Ambient temperature

Standard：-20～70℃ Option：-40～70℃

Note) When operating below -20℃, visibility of the LCD display may be worse.

Signal cable (Remote type: between sensor and transmitter) Impedance 100～200Ω

Withstand voltage 120V Outer diameter 6～12mm

Cable design 4 core shielded cable (2 wire pairs as a star-quad cable) Max. signal cable length

0.25mm²	：	50m
0.34mm²	：	100m
0.50mm²	：	150m
0.75mm²	：	200m

Power

AC Power Terminal Operating voltage Power consumption	：：：	L／N 100～240VAC 50/60Hz 20VA
DC Power Terminal	：	1+／2-
Operating voltage	：	11～30VDC
Power consumption	：	20W

Output

Standard output

Current output

Current output	Active mode	Passive mode
Terminal	Uco(+)／32(-)	31(+)／32(-)
Output signal	4～20mADCor4～12～20mADC Switchable	4～20mADC
Load resistance	250～300Ω	250～600Ω
Source voltage	－	12～30V
Measuring error	0.1% or less of measured value

Digital output

Digital output	Pulse/frequency output (passive)	Binary output (passive)
Terminal	41(+)／42(-)、51(+)／52(-)	41(+)／42(-)、51(+)／52(-)
Output “closed”	Voltage 3VDC or less 2.5kHz or less：2～30mA More than 2.5kHz：10～30mA	Voltage 3VDC or less 2～30mA
Output “open”	Voltage 16～30VDC 0.2mA or less	Voltage 16～30VDC 0.2mA or less
Max. frequency	10.5kHz	－
Pulse width	0.1～2,000ms	－

Option output

Option (by plug-in card)

Passive current output (red)

Terminal	V1(+)／V2(-)、V3(+)／V4(-)	The plug-in card can be used in slot OC1 or OC2
Output signal	4～20mA
Load resistance	250～600Ω
Source voltage	12～30VDC
Measuring error	0.1% or less of measured value

Digital output (green): Binary output (Passive)

Terminal	V1／V2、V3／V4	The plug-in card can be used in slot OC1 or OC2
Output “closed”	Voltage 3VDC or less 2～30mA
Output “open”	Voltage 16～30VDC 0.2mA or less

Digital input (Yellow)

Terminal	V1(+)／V2(-)、V3(+)／V4(-)	The plug-in card can be used in slot OC1 or OC2
Input “ON”	Voltage 16V～30VDC
Input “OFF”	Voltage 3VDC or less
Internal resistance	6.5kΩ

24VDC Power supply (blue)

Terminal	V1(+)／V2(-)	The plug-in card can be used in slot OC1 only.
Function	For active connection of passive outputs
Output voltage	24VDC at 0mA 17VDC at 25mA
Load rating	25mA, permanently short circuit-proof

Article

Specification code

Note

Model

FB450

Coliolis Mass flow meter / High accuracy type

FB430

Coliolis Mass flow meter / General type

Explosion Protection Certificate

General Purpose

ATEX/IECEx （Zone 2/22）

ATEX/IECEx （Zone 1/21）

cFMus version Class 1 Div. 2 （Zone 2/21）

cFMus version Class 1 Div. 1 （Zone 1/21）

Transmitter type / Material / Cable Gland

When select "Unit type"

Remote type／Aluminum／1-M20×1.5

Remote type／Aluminum／1-NPT1/2

Remote type／Stainless／1-M20×1.5

Remote type／Stainless／1-NPT1/2

Meter size / Connection size

015E1

015/10A（3/8B）

015R0

015/15A（1/2B） : Standard

015R1

015/20A（3/4B）

025E1

025/20A（3/4B）

025R0

025/25A（1B） : Standard

025R2

025/40A（1-1/2B）

050E1

050/40A（1-1/2B）

050R0

050/50A（1B） : Standard

050R1

050/65A（2-1/2B）

080E1

080/65A（2-1/2B）

080R0

080/80A（3B） : Standard

080R1

080/100A（4B）

100E1

100/80A（3B）

100R0

100/100A（4B） : Standard

100R2

100/150A（6B）

150E2

150/100A（4B）

150R0

150/150A（6B） : Standard

150R2

150/200A（8B）

Process Connection Type

Flange JIS 10K

Flange JIS 20K

Flange DIN PN16

Flange DIN PN40

Flange DIN PN63

Flange DIN PN100

Flange ANSI/ASME B16.5 Class 150

Flange ANSI/ASME B16.5 Class 300

Flange ANSI/ASME B16.5 Class 600

Flange ANSI/ASME B16.5 Class 900

Flange ANSI/ASME B16.5 Class 1500

In accordance with DIN 32676 Tri-clamp

In accordance with ASME BPE Tri-clamp

In accordance with DIN 11851 Fitting

Material of Wetted Parts

Stainless steel

Ni-Alloy （Alloy-C）

Flow Calibration

Flow forward：Liquid±0.4 %, Gas：±1.0 %・・・・・・General type

Flow forward：Liquid±0.25 %, Gas：±1.0 %・・・・・General type

Flow forward：Liquid±0.2 %, Gas：±1.0 %・・・・・・General type

Flow forward：Liquid±0.15 %, Gas：±0.5 %・・・・・High accuracy type

Flow forward：Liquid±0.1 %, Gas：±0.5 %・・・・・・High accuracy type

Flow forward/reverse：Liquid±0.4 %, Gas：±1.0 %・・・・・・General type

Flow forward/reverse：Liquid±0.25 %, Gas：±1.0 %・・・・・General type

Flow forward/reverse：Liquid±0.2 %, Gas：±1.0 %・・・・・・General type

Flow forward/reverse：Liquid±0.15 %, Gas：±0.5 %・・・・・High accuracy type

Flow forward/reverse：Liquid±0.1 %, Gas：±0.5 %・・・・・・High accuracy type

Density Calibration

Density 10 g/L・・・・・General type

Density 2 g/L・・・・・・High accuracy type

Density 1 g/L・・・・・・High accuracy type

Others

Transmitter Type / Material / Cable Grand

Unit type／Aluminum／3-M20×1.5

Unit type／Aluminum／3-NPT1/2

Unit type／Aluminum／3-NPT1/2（Explosion protection）

Unit type／Aluminum／3-M20×1.5（Explosion protection）

When select "Remote type"

Output

Current output 1（AorP）, Digital output 1&2（P）、HART

Current output 1（AorP）, Digital output 1&2（P）、24VDC loop supply、HART

Current output 1（A）, Digital output 1&2（P）, current output 2（P）、HART

Current output 1（A）, Digital output 1&2（P）, current output 2＆3（P）、HART

Without: when select remote type

Power supply

100～230VAC

11～30VDC

Without: when select remote type

Sensor option

Article	Additional specification code								Note
Additional output 1	DRN								1×Digital input
	DRG								1×Digital output
	DRA								1×Analog output（P）（4～20mA）
	DRT								24VDC transmitter loop power supply
Additional output 2		DSN							1×Digital input
		DSG							1×Digital output
		DSA							1×Analog output（P）（4～20mA）
Special operation mode			N6						Standard + DensiMass ： concentration measurement :only 450 type
			N5						Standard + Filling application
			N7						VeriMass function： Meter verification : omly 450 type
Pressure-resistance Sensor Housing				PR5					Max. burst pressure 6MPa (Include tower length extension)
				PR6					Max. burst pressure 10MPa(Include tower length extension)：Meter size 015
				PR7					Max. burst pressure 15MPa(Include tower length extension)：Meter size 015
Signal Cable Length					SC0				Without
					SC1				5m
					SC2				10m
					SC4				20m
					SC5				25m
					SC6				30m
					SC8				40m
					SCA				50m
					SCE				100m
					SCG				150m
					SCJ				200m
TAG No. Plate						T1			With TAG No. Plate
Anmbient Temperature Range							TA9		-40～70℃
Extend Tower Length								TE1	Tower length extension 1, Meter insukation Single
								TE2	Tower length extension 2, Meter insukation Double

Note) P：Passive mode

Remote type (Transmitter)

Article	Specification code					Note
Model	FT450					Coliolis Mass flow meter High accuracy type
	FT430					Coliolis Mass flow meter General type
Explosion Protection Certificate		Y0				General Purpose
		A2				ATEX/IECEx （Zone 2/22）
		A1				ATEX/IECEx （Zone 1/21）
		F2				cFMus version Class 1 Div 2（Zone 2/21）
		F1				cFMus version Class 1 Div 1（Zone 1/21）
Transmitter type / Material / Cable Grand			R1			Remote type／Aluminum／1-M20×1.5
			R2			Remote type／Aluminum／1-NPT1/2
			R5			Remote type／Staineless／1-M20×1.5
			R6			Remote type／Staineless／1-NPT1/2
Output				G0		Current output 1（AorP）, Digital output 1&2（P）、HART
				G1		Current output 1（AorP）, Digital output 1&2（P）, 24VDC loop power, HART
				G2		Current output 1（A）, Digital output 1&2（P）, Current output 2（P）, HART
				G3		Current output 1（A）, Digital output 1&2（P）, Current output2＆3（P）, HART
Power supplu					A	100～230VAC
					C	11～30VDC

Option －

Mounting Bracket Shape/ Material	B1				2B Pipe mounting / Carbon steel
Additional output 1		DRN			1×Digital input
		DRG			1×Digital output
		DRA			1×Analog output（P）（4～20mA）
		DRT			24VDC transmitter loop power supply
Additional output 2			DSN		1×Digital input
			DSG		1×Digital output
			DSA		1×Analog output（P）（4～20mA）
TAG No. Plate				T1	With TAG No.Plate